A Calculation Method of Overall Stability for Flat Plate Stiffened Panels Under Compression

ZHAO Qiu; CHEN Peng; LIN Zhiping; ZHANG Junchao

doi:10.3724/j.gyjzG22020911

Volume 54 Issue 10

Oct. 2024

Turn off MathJax

Article Contents

Article Navigation > INDUSTRIAL CONSTRUCTION > 2024 > 54(10): 138-146

ZHAO Qiu, CHEN Peng, LIN Zhiping, ZHANG Junchao. A Calculation Method of Overall Stability for Flat Plate Stiffened Panels Under Compression[J]. INDUSTRIAL CONSTRUCTION, 2024, 54(10): 138-146. doi: 10.3724/j.gyjzG22020911

Citation:

ZHAO Qiu, CHEN Peng, LIN Zhiping, ZHANG Junchao. A Calculation Method of Overall Stability for Flat Plate Stiffened Panels Under Compression[J]. INDUSTRIAL CONSTRUCTION, 2024, 54(10): 138-146. doi: 10.3724/j.gyjzG22020911

Citation:

PDF( 16036 KB)

A Calculation Method of Overall Stability for Flat Plate Stiffened Panels Under Compression

doi: 10.3724/j.gyjzG22020911

1. School of Civil Engineering, Fuzhou University, Fuzhou 350108, China;
2. Fujian Highway Bridge Construction & Development Co., Ltd., Xiamen 361000, China;
3. Fujian Highway Engineering Key Laboratory, Xiamen 361000, China

Received Date: 2022-02-09
Available Online: 2024-11-06

Abstract

Abstract

Flat panel stiffened plates are the basic components of steel box, steel tower and steel arch in steel structure bridges. In order to study the overall stability of flat panel stiffened plates, the finite element models verified by experiments were established for overall stability analysis. The effects of different constitutive relations, initial geometric defects and welding residual stresses on the overall stability bearing capacity were considered. It was found that: the ideal elastic-plastic constitutive model could be used to safely analyze the overall stability of flat plate stiffened panel under compression. Increasing the initial bending amplitude and loading eccentricity of the model would weaken the plates’ overall stability capacity.When the defect amplitude was 1/1 000 of the calculated length, the bearing capacity of model initially bent on the side of the plate rib was relatively low, but the model initially bent on the side of the stiffened plate was more sensitive to the defect; increasing the peak value of welding residual compressive stress would reduce the overall axial stiffness and ultimate average stress of flat plate stiffened panels.Within the range of the relative slenderness ratio studied, the fitted calculation formula curve was lower than the test value and the curve of equal strength steel u-rib column, and was generally close to the class B column curve in the Specifications for Design of Highway Steel Bridge (JTG D64—2015), higher than the column curve corresponding to the Japanese and American codes, which could be safely used for the overall stability calculation of flat panel stiffened plates.
- bridge engineering,
- flat plate stiffened panel,
- overall stability,
- numerical simulation,
- stability capacity,
- calculation method

FullText(HTML)

References(18)

References

[1]	BAI L H, SHEN R L, WANG L, et al. Experimental and numerical study on buckling behavior of a rigidly stiffened plate with tee ribs[J]. International Journal of Steel Structures, 2018,18(2018): 582-595.
[2]	DING H P, SHEN Q H, DU S D, et al. Structural condition assessment of the herringbone middle pylon of the Taizhou Bridge using SHM strain data[J]. Journal of Sensors,2017,2017(1):1-10.
[3]	MA B, LIN Y P, ZHANG J J. Decade review: bridge type selection and challenges of Lupu Bridge[J]. Structural Engineering International, 2013, 23(3):317-322.
[4]	赵秋,翟战胜,陈宝春. 混合强度U形肋加劲钢板受压稳定试验研究[J].建筑结构学报,2016,37(7):54-63.
[5]	秦凤江,狄谨,周绪红,等. 钢箱梁U型肋加劲板受压稳定极限承载力影响因素分析[J].长安大学学报(自然科学版),2017,37(1):58-66.
[6]	赵秋,张骏超,翟战胜,等. U肋加劲板受压力学性能分析[J].铁道建筑,2019,59(5):15-21.
[7]	赵秋,张骏超,林楚,等. 混合钢U肋加劲板受压整体稳定承载力数值模拟与计算方法[J].建筑科学与工程学报,2020,37(3):45-54.
[8]	SADAMOTO S, TANAKA S, TANIGUCHI K, et al. Buckling analysis of stiffened plate structures by an improved meshfree flat shell formulation[J]. Thin-Walled Structures, 2017, 117: 303-313.
[9]	SHIN D, DAT B, KIM K. Compressive strength of HPS box girder flanges stiffened with open ribs[J]. Journal of Constructional Steel Research, 2014, 95(1): 230-241.
[10]	甘采华,王华,刘世建.开口加劲板件的稳定极限承载力研究[J].公路工程,2021,46(2):234-240.
[11]	赵秋,高璞.受压加劲板稳定承载力计算方法比较[J].福州大学学报(自然科学版),2014,42(1):123-127.
[12]	赵秋, 翟战胜.开口肋加劲板屈曲模态与临界屈曲应力分析[J]. 建筑科学与工程学报, 2016, 33(2):48-55.
[13]	LI C F, REN H L, ZHU Z Y, et al. Numerical investigation on the ultimate strength of aluminium integrally stiffened panels subjected to uniaxial compressive load[J]. Thin-Walled Structures, 2018, 127: 221-234.
[14]	陈建桂.开口肋加劲板焊接残余应力分布与简化计算方法研究[D].福州:福州大学,2018.
[15]	中华人民共和国住房和城乡建设部. 钢结构设计标准:GB 50017—2017[S]. 北京: 中国建筑工业出版社, 2018.
[16]	中华人民共和国交通运输部. 公路钢结构桥梁设计规范:JTG D64—2015[S]. 北京: 人民交通出版社, 2015.
[17]	日本道路协会. 道路桥示方书·同解说(Ⅱ钢桥篇)[S]. 东京:丸善株式会社,2002.
[18]	American Association of State Highway and Transportation Officials(AASHTO). AASHTO LRFD bridge design specifications[S].Washington DC: AASHTO, 2007.