A REVIEW OF INCORPORATING REINFORCEMENT METHOD IN 3D CONCRETE PRINTING

LIU Tianhao; WANG Li; LI Zhijian; MA Guowei; SU Lichao

doi:10.13204/j.gyjzG21031901

Volume 51 Issue 6

Oct. 2021

Turn off MathJax

Article Contents

Article Navigation > INDUSTRIAL CONSTRUCTION > 2021 > 51(6): 9-15

LIU Tianhao, WANG Li, LI Zhijian, MA Guowei, SU Lichao. A REVIEW OF INCORPORATING REINFORCEMENT METHOD IN 3D CONCRETE PRINTING[J]. INDUSTRIAL CONSTRUCTION, 2021, 51(6): 9-15. doi: 10.13204/j.gyjzG21031901

Citation:

LIU Tianhao, WANG Li, LI Zhijian, MA Guowei, SU Lichao. A REVIEW OF INCORPORATING REINFORCEMENT METHOD IN 3D CONCRETE PRINTING[J]. INDUSTRIAL CONSTRUCTION, 2021, 51(6): 9-15. doi: 10.13204/j.gyjzG21031901

Citation:

PDF( 12559 KB)

A REVIEW OF INCORPORATING REINFORCEMENT METHOD IN 3D CONCRETE PRINTING

doi: 10.13204/j.gyjzG21031901

1. School of Civil and Transportation, Hebei University of Technology, Tianjin 300401, China;
2. Xingtai Road and Bridge Construction Corporation, Xingtai 054001, China

Received Date: 2021-03-19
Available Online: 2021-10-27

Abstract

Abstract

In recent years, 3D printing has attracted widespread attention and has been successfully applied in the field of civil engineering. The layer-by-layer additive manufacturing method gives it a high degree of flexibility, but it is difficult to achieve the simultaneous implantation of the steel cage, which greatly limits its engineering application. Efficient reinforcement and toughening methods are the core and key to the structural application of 3D concrete printing. The toughening methods and research results of 3D printed concrete structures at home and abroad were summarited, the advantages, characteristics, and applicability of various methods were compared and analyzed. This paper aimed to provide scientific and reasonable suggestions for the improvement of bearing safety of 3D printed concrete structures and further promoting the practical application of 3D concrete printing technique.
- 3D concrete printing,
- tonghening by reinforcement,
- mechanical properties,
- intelligent construction

FullText(HTML)

References(43)

References

[1]	田伟, 肖绪文, 苗冬梅. 建筑3D打印发展现状及展望[J]. 施工技术, 2015, 44(17):79-83.
[2]	雷斌, 马勇, 熊悦辰, 等. 3D打印混凝土材料制备方法研究[J]. 混凝土, 2018(2):145-53.
[3]	刘致远, 王振地, 王玲, 等. 3D打印水泥基材料工作性分析与表征[J]. 低温建筑技术, 2018, 40(6):11-16.
[4]	MA G, WANG L. A Critical Review of Preparation Design and Workability Measurement of Concrete Material for Largescale 3D Printing[J]. Frontiers of Structural and Civil Engineering, 2018, 12(3):382-400.
[5]	SALET T A M, AHMED Z Y, BOS F P, et al. Design of a 3D Printed Concrete Bridge by Testing[J]. Virtual and Physical Prototyping, 2018, 13(3):222-236.
[6]	南京绿色增材制造研究院有限公司. 南京江北新区公交站台[EB/OL]. (2020-06-20)[2021-02-10]. http://www.nanjingiam.com/cases.html?id=21.
[7]	徐卫国. 世界最大的混凝土3D打印步行桥[J]. 建筑技艺, 2019(2):6-9.
[8]	World's First 3D Printed Reinforced Concrete Bridge Opened[EB/OL]. (2017-10-07)[2021-02-10]. https://www.tue.nl/en/our-university/departments/built-environment/news/17-10-2017-worlds-first-3D-printed-reinforced-concrete-bridge-opened/.
[9]	XU J, DING L Y, LOVE P E D. Digital Reproduction of Historical Building Ornamental Components:From 3D Scanning to 3D Printing[J]. Automation in Construction, 2017, 76:85-96.
[10]	ZHANG Y, ZHANG Y S, LIU G, et al. Fresh Properties of a Novel 3D Printing Concrete Ink[J]. Construction and Building Materials, 2018, 174:263-271.
[11]	ZHANG Y, ZHANG Y S, SHE W, et al. Rheological and Harden Properties of the High-Thixotropy 3D Printing Concrete[J]. Construction and Building Materials, 2019, 201:278-285.
[12]	BOS F P, BOSCO E, SALET T A M. Ductility of 3D Printed Concrete Reinforced with Short Straight Steel Fibers[J]. Virtual and Physical Prototyping, 2019, 14(2):160-174.
[13]	NEMATOLLAHI B, XIA M, SANJAYAN J, et al. Effect of Type of Fiber on Inter-Layer Bond and Flexural Strengths of Extrusion-Based 3D Printed Geopolymer[J]. Materials Science Forum, 2018, 939:155-162.
[14]	SOLTAN D G, LI V C. A Self-Reinforced Cementitious Composite for Building-Scale 3D Printing[J]. Cement and Concrete Composites, 2018, 90:1-13.
[15]	OGURA H, NERELLA V, MECHTCHERINE V. Developing and Testing of Strain-Hardening Cement-Based Composites (SHCC) in the Context of 3D-Printing[J]. Materials, 2018, 11(8):1375.
[16]	PANDA B, PAUL S C, TAN M J. Anisotropic Mechanical Performance of 3D Printed Fiber Reinforced Sustainable Construction Material[J]. Materials Letters, 2017, 209:146-149.
[17]	HAMBACH M, MOLLER H, NEUMANN T, et al. Portland Cement Paste with Aligned Carbon Fibers Exhibiting Exceptionally High Flexural Strength (>100 MPa)[J]. Cement and Concrete Research, 2016, 89:80-86.
[18]	CHRIST S, SCHNABEL M, VORNDRAN E, et al. Fiber Reinforcement During 3D Printing[J]. Materials Letters, 2015, 139:165-168.
[19]	HAMBACH M, VOLKMER D. Properties of 3D-Printed Fiber-Reinforced Portland Cement Paste[J]. Cement & Concrete Composites, 2017, 79:62-70.
[20]	MA G, LI Z, WANG L, et al. Mechanical Anisotropy of Aligned Fiber Reinforced Composite for Extrusion-Based 3D Printing[J]. Construction and Building Materials, 2019, 202:770-783.
[21]	ASPRONE D, MENNA C, BOS F P, et al. Rethinking Reinforcement for Digital Fabrication with Concrete[J]. Cement & Concrete Research, 2018, 112:111-121.
[22]	HACK N, LAUER W V. Mesh-Mould:Robotically Fabricated Spatial Meshes as Reinforced Concrete Formwork[J]. Architectural Design, 2014, 84(3):44-53.
[23]	CLASSEN M, UNGERMANN J, SHARMA R. Additive Manufacturing of Reinforced Concrete-Development of a 3D Printing Technology for Cementitious Composites with Metallic Reinforcement[J]. Applied Sciences, 2020(10). DOI: 10.3390/app10113791.
[24]	PERROT A, JACQUET Y, RANGEARD D, et al. Nailing of Layers:A Promising Way to Reinforce Concrete 3D Printing Structures[J]. Materials, 2020, 13(7). DOI: 10.3390/ma13071518.
[25]	谭思. 这座3D打印的房子能抗8级地震[EB/OL]. (2016-07-31 )[2021-02-10].https://tech.qq.com/a/20160731/003223.htm.
[26]	MARCHMENT T, SANJAYAN J. Mesh Reinforcing Method for 3D Concrete Printing[J]. Automation in Construction, 2020, 109. DOI: 10.1016/j.autcon.2019.102992.
[27]	HEGGER J, CURBACH M, STARK A, et al. Innovative Design Concepts:Application of Textile Reinforced Concrete to Shell Structures[J]. Structural Concrete, 2018, 19(3):637-646.
[28]	VERGARA E C, AGUIRREGABIRIA B L, PEREZ J M L, et al. Innovative Free-Form Glass Fiber Reinforced Concrete (GRC) Panel[J]. Revista De La Construccion, 2017, 16(3):479-488.
[29]	AKHNOUKH A K, XIE H. Welded Wire Reinforcement Versus Random Steel Fibers in Precast/Prestressed Ultra-High Performance Concrete I-Girders[J]. Construction and Building Materials, 2010, 24(11):2200-2207.
[30]	ASPRONE D, AURICCHIO F, MENNA C, et al. 3D Printing of Reinforced Concrete Elements:Technology and Design Approach[J]. Construction and Building Materials, 2018, 165:218-231.
[31]	葛杰, 白洁, 杨燕, 等. 3D打印配筋砌体墙承载力试验研究[J]. 建筑材料学报, 2020, 23(2):414-420.
[32]	LIM S, LE T, WEBSTER J, et al. Fabricating Construction Components Using Layered Manufacturing Technology[C]//Global Innovation in Construction Conference.UK:2009:13-16.
[33]	LIM S, BUSWELL R A, LE T T, et al. Development of a Viable Concrete Printing Process[C]//28th International Symposium on Automation and Robotics in Construction. Seoul:2011:665-670.
[34]	KHOSHNEVIS B, HWANG D, YAO K T, et al. Mega-Scale Fabrication by Contour Crafting[J]. International Journal of Industrial Systems Engineering, 2006, 1(3):301-320.
[35]	WU P, WANG J, WANG X. A Critical Review of the Use of 3-D Printing in the Construction Industry[J]. Automation in Construction, 2016, 68:21-31.
[36]	葛杰, 马荣全, 苗冬梅, 等. 3D打印建筑材料层间粘结性能试验研究[J]. 建筑结构, 2017, 47(4):49-52.
[37]	VANTYGHEM G, DE CORTE W, SHAKOUR E, et al. 3D Printing of a Post-Tensioned Concrete Girder Designed by Topology Optimization[J]. Automation in Construction, 2020, 112. DOI: 10.1016/j.autcon.2020.103084.
[38]	FARINA I, FABBROCINO F, CARPENTIERI G, et al. On the Reinforcement of Cement Mortars through 3D Printed Polymeric and Metallic Fibers[J]. Composites Part B:Engineering, 2016, 90:76-85.
[39]	MECHTCHERINE V, GRAFE J, NERELLA V N, et al. 3D-Printed Steel Reinforcement for Digital Concrete Construction-Manufacture, Mechanical Properties and Bond Behaviour[J]. Construction and Building Materials, 2018, 179:125-137.
[40]	BOS F, AHMED Z, JUTINOV E, et al. Experimental Exploration of Metal Cable as Reinforcement in 3D Printed Concrete[J]. Materials, 2017, 10(11). DOI: 10.3390/ma10111314.
[41]	LI Z, WANG L, MA G. Mechanical Improvement of Continuous Steel Microcable Reinforced Geopolymer Composites for 3D Printing Subjected to Different Loading Conditions[J]. Composites Part B:Engineering, 2020, 187. DOI: 10.1016/j.compositesb.2020.107796.
[42]	MA G, LI Z, WANG L, et al. Micro-Cable Reinforced Geopolymer Composite for Extrusion-Based 3D Printing[J]. Materials Letters, 2019, 235:144-147.
[43]	LIM J H, PANDA B, PHAM Q C. Improving Flexural Characteristics of 3D Printed Geopolymer Composites with in-Process Steel Cable Reinforcement[J]. Construction and Building Materials, 2018, 178:32-41.