CRITICAL LATERAL SLENDERNESS RATIO OF STEEL BEAMS IN PLASTIC DESIGN

Liu Yang; Tong Lewei

doi:10.13204/j.gyjz201405029

Volume 44 Issue 05

Jul. 2015

Turn off MathJax

Article Contents

Abstract

References

Article Navigation > INDUSTRIAL CONSTRUCTION > 2014 > 44(05): 132-139

CHANG Hong, LIU Jinnan, MENG Qingyu. EXPERIMENTAL STUDY ON THERMO-MECHANICAL PROPERTIES OF ENERGY PILES UNDER ACTION OF CYCLIC TEMPERATURE[J]. INDUSTRIAL CONSTRUCTION, 2021, 51(1): 125-130. doi: 10.13204/j.gyjzG20041107

Citation:

Liu Yang, Tong Lewei. CRITICAL LATERAL SLENDERNESS RATIO OF STEEL BEAMS IN PLASTIC DESIGN[J]. INDUSTRIAL CONSTRUCTION, 2014, 44(05): 132-139. doi: 10.13204/j.gyjz201405029

Citation:

Liu Yang, Tong Lewei. CRITICAL LATERAL SLENDERNESS RATIO OF STEEL BEAMS IN PLASTIC DESIGN[J]. INDUSTRIAL CONSTRUCTION, 2014, 44(05): 132-139. doi: 10.13204/j.gyjz201405029

PDF( 0 KB)

CRITICAL LATERAL SLENDERNESS RATIO OF STEEL BEAMS IN PLASTIC DESIGN

doi: 10.13204/j.gyjz201405029

Publish Date: 2014-05-20

Abstract

Abstract

When the lateral slenderness ratio of a steel beam reaches a critical value during plastic design，it is necessary to set lateral supports so as to prevent lateral flexural-torsional buckling and then ensure sufficient rotation capacity． Thus，the rotation capacity required by a steel beam is generally lower in engineering practice． However， higher rotation capacity was specified in The Code for Design of Steel Structure ( GB 500172003) which caused the critical lateral slenderness ratio from formula was too small． For this reason，the nonlinear finite element modeling for numerical analysis of steel beams was developed in this paper． The calculated results agreed well with the other scholarsexperimental results． Based on the analysis of five influence parameters such as end-moment ratio，web height-thickness ratio，flange width-thickness ratio，residual stress distribution，out-of-plane boundary condition，and using reasonable criterion for rotation capacity，a simplified formula for critical lateral slenderness ratio was proposed， which could deal with four parameters except flange width-thickness ratio． The formula proposed was more reasonable and practical，compared with the formula in The Code for Design of Steel Structure( GB 500172003) ．
- steel beams,
- plastic design,
- rotation capacity,
- critical lateral slenderness ratio,
- suggested formula

FullText(HTML)

References(0)

References

Relative Articles

[1]	PENG Daibin, LIU Zhanke. Research on Critical Moment of Lateral Restrained Beams Under End Moments[J]. INDUSTRIAL CONSTRUCTION, 2023, 53(2): 144-150. doi: 10.13204/j.gyjzG20082506
[2]	CHU Liusheng, YAN Zenghui, TIAN Ye, YUAN Chengfang. A Resilience Model for Joints Between Steel-Reinforced Concrete Columns and Steel Beams Considering the Effect of Floor Slabs in a Shear Failure Mode[J]. INDUSTRIAL CONSTRUCTION, 2023, 53(1): 175-181,90. doi: 10.13204/j.gyjzG20122911
[3]	ZHU Qunhong, TONG Ji, TONG Genshu. Effects of Openings on Steel Beams and its Design Suggestions[J]. INDUSTRIAL CONSTRUCTION, 2022, 52(1): 90-97. doi: 10.13204/j.gyjzG21122107
[4]	KONG Deliang, XU Shanhua, NIE Biao. EXPERIMENTAL RESEARCH ON FLEXURAL PROPERTIES OF CORRODED H-SHAPED STEEL BEAMS[J]. INDUSTRIAL CONSTRUCTION, 2021, 51(3): 98-103. doi: 10.13204/j.gyjzG20102707
[6]	Tong Genshu. A RESTUDY ON STABILITY OF STEEL BEAMS(Ⅲ):COMPARISON AMONG CODES AND RELIABILITY ANALYSIS[J]. INDUSTRIAL CONSTRUCTION, 2014, 44(03): 162-168. doi: 10.13204/j.gyjz201403032
[7]	A RESTUDY ON STABILITY OF STEEL BEAMS: INTERNATIONAL TESTS AND THEORETICAL ANALYSES( Ⅱ)[J]. INDUSTRIAL CONSTRUCTION, 2014, 44(02): 142-146. doi: 10.13204/j.gyjz201402030
[8]	Tong Genshu. A RESTUDY ON STABILITY OF STEEL BEAMS: RECENT RESEARCHES IN CHINA AND SUGGESTIONS( Ⅳ)[J]. INDUSTRIAL CONSTRUCTION, 2014, 44(04): 146-151.
[9]	Nie Jianguo, Zhu Dan. EXPERIMENTAL STUDY ON PULLING CAPABILITY OF CONCRETE WALL-STEEL BEAM T-PLATE PIN JOINT[J]. INDUSTRIAL CONSTRUCTION, 2013, 43(12): 149-155. doi: 10.13204/j.gyjz201312028
[10]	Zheng Yun, Yue Qingrui, Chen Xuan, Li Zhongyu. FATIGUE TEST RESEARCH ON CFRP STRENGTHENED STEEL BEAM[J]. INDUSTRIAL CONSTRUCTION, 2013, 43(5): 148-152. doi: 10.13204/j.gyjz201305031
[13]	Li Shulin, Li Shuxiang, Wan Bo, Li Ying. ANALYSIS AND DESIGN OF THE CRANE INSTALLED ON TOP OF THE EXISTING FRAMEWORK BUILDING[J]. INDUSTRIAL CONSTRUCTION, 2006, 36(11): 98-101,105. doi: 10.13204/j.gyjz200611024
[14]	Chen Zhihua, Li Yang, Shi Jie. APPLICATION STUDY ON THE SPATIAL CURVE TAPERED BOX GIRDER FOR TIANJIN MUSEUM[J]. INDUSTRIAL CONSTRUCTION, 2005, 35(12): 75-77. doi: 10.13204/j.gyjz200512020
[15]	Li Guoqiang, Ding Jun, Zhang Ren. A PRACTICAL APPROACH FOR FIRE-RESISTANT CALCULATION AND DESIGN OF FIRE-RESISTANT STEEL BEAMS[J]. INDUSTRIAL CONSTRUCTION, 2005, 35(7): 80-82. doi: 10.13204/j.gyjz200507023
[16]	Li Peng, Xu Dexing, Zhang Hanmin. EXPERIMENTAL RESEARCH ON STRENGTHENING STEEL STRUCTURES WITH CARBON FIBER REINFORCED POLYMER[J]. INDUSTRIAL CONSTRUCTION, 2004, 34(7): 91-92,98. doi: 10.13204/j.gyjz200407027