EXPERIMENTAL RESEARCH ON NOTCHED CONNECTION FOR GLUBAM-CONCRETE COMPOSITE BEAMS

Shan Bo; Liang Longhui; Xiao Yan; Zhang Weiliang

doi:10.13204/j.gyjz201504004

Volume 45 Issue 4

Jun. 2015

Turn off MathJax

Article Contents

Abstract

References

Article Navigation > INDUSTRIAL CONSTRUCTION > 2015 > 45(4): 18-25

Ma Hui, Xu Jianyang, Zhao Hongtie. ANALYSIS OF RESPONSE OF ANCIENT TIMBER BUILDINGS ON THE HIGH PEDESTAL UNDER RANDOM EARTHQUAKE EXCITATIONS[J]. INDUSTRIAL CONSTRUCTION, 2014, 44(02): 45-49. doi: 10.13204/j.gyjz201402011

Citation:

Shan Bo, Liang Longhui, Xiao Yan, Zhang Weiliang. EXPERIMENTAL RESEARCH ON NOTCHED CONNECTION FOR GLUBAM-CONCRETE COMPOSITE BEAMS[J]. INDUSTRIAL CONSTRUCTION, 2015, 45(4): 18-25. doi: 10.13204/j.gyjz201504004

Citation:

PDF( 0 KB)

EXPERIMENTAL RESEARCH ON NOTCHED CONNECTION FOR GLUBAM-CONCRETE COMPOSITE BEAMS

doi: 10.13204/j.gyjz201504004

Publish Date: 2015-04-20

Abstract

Abstract

Selecting composite connection is a crucial factor for researching mechanical performance of GluBamconcrete composite beam． An initial stage of research on the feasibility of a type of notched connection for GluBamconcrete composite beam was described． Total 15 groups of bond and anchorage pull-out tests and 3 groups of shearslip tests were conducted respectively． The main mechanical properties such as anchoring capacity，load-slip curves and anti-slip stiffness were measured． The test results showed that liquid adhesive could penetrate GluBam easier and reach higher anchoring strength compared to paste adhesive． There was an optimum diameter for glued-in rebar according to the standardized anchorage strength，which almost did not fluctuate with anchorage depth． Setting inclination on the bearing surface of notched connector could not improve mechanical properties of this type of composite beams． But nailed to sides of GluBam beam prevented cracking of GluBam beam effectively and increased shear capacity significantly． Compared with GluLam-concrete composite beam with the similar notched connector，this type of new connector presents good mechanical performance while improved ductility． However only qualitative conclusions can be drawn at this stage，which needs to be investigated further．
- composite beams,
- GluBam-concrete structures,
- GluBam,
- shear connectors

FullText(HTML)

References(0)

References

Relative Articles

[1]	LIN Wenluo, LI Junhua, TAN Jie. Experimental Research on Shear Performance of Stainless Steel Connectors in a New Type of Prefabricated Concrete Sandwich Insulation Wall Panels[J]. INDUSTRIAL CONSTRUCTION, 2024, 54(4): 64-71. doi: 10.13204/j.gyjzG23050606
[2]	ZHANG Yumin, XU Zhenhua, LI Jinghui, FENG Xuanming, WANG Yuliang. Research on Mechanical Properties of Stainless Steel Connectors of Precast Concrete Sandwich Walls[J]. INDUSTRIAL CONSTRUCTION, 2023, 53(8): 38-42. doi: 10.13204/j.gyjzG22031303
[3]	SHENG Zhigang, CHEN Xing, PAN Peng. Experimental Research on Influence Factors to Bearing Capacity and Stiffness Degradation of Small Concrete Block Walls[J]. INDUSTRIAL CONSTRUCTION, 2023, 53(10): 94-99. doi: 10.13204/j.gyjzG22071404
[4]	CHEN Shuhui, XIA Zhanghua, WU Zelin, XU Yousheng, HU Mingliang, ZHU Sanfan. The Shear Bearing Capacity of Prefabricated UHPC Utility Tunnels[J]. INDUSTRIAL CONSTRUCTION, 2023, 53(5): 158-164. doi: 10.13204/j.gyjzG22010413
[5]	CHEN Yang, NING Jian, REN Chong, YANG Yong. Numerical Study on Shear Performance of Grouped Large Headed Stud Connectors in Prefabricated Steel-Thin UHPC Composite Girder[J]. INDUSTRIAL CONSTRUCTION, 2023, 53(12): 164-174. doi: 10.13204/j.gyjzG23070905
[6]	ZHANG Chenrong, YAN Jingliang, LIU Xiaogang. Research on Tensile and Shear Performance of Fully-Prefabricated Slabs with UHPC Split-Joints[J]. INDUSTRIAL CONSTRUCTION, 2023, 53(9): 119-127. doi: 10.13204/j.gyjzG23022811
[7]	XIE Zhiqiang, SHI Leilei, ZHANG Ailin, ZHOU Daxing, ZHANG Xiangdong, YIN Bingshuai, WANG Kai. Research on Simplified Analysis Methods of Nonlinear Finite Element for Shear Performance of Self-Piercing Riveting Connections Between Cold-Formed Steel Sheets[J]. INDUSTRIAL CONSTRUCTION, 2022, 52(5): 98-105,146. doi: 10.13204/j.gyjzG22011912
[8]	WANG Jingfeng, WANG Wanqian, ZHANG Rong, LIU Chao, ZHANG Huijie, WANG Can. EXPERIMENTAL STUDY ON SHEAR PERFORMANCES OF PREFABRICATED COLD-FORMED THIN-WALL STEEL WALLS FILLED WITH LIGHT WEIGHT POLYMER MORTAR[J]. INDUSTRIAL CONSTRUCTION, 2021, 51(7): 145-150,202. doi: 10.13204/j.gyjzG20070402
[9]	YIN Zhan, ZHANG Yueguo, YANG Sizhong, REN Chengchuan, ZHOU Jian, LIU Xinghua, YU Yinquan. EXPERIMENTAL RESEARCH ON TENSILE AND SHEAR ACTION OF TRUSS CONNECTIONS OF LOW-ENERGY SANDWICH INSULATION WALLS[J]. INDUSTRIAL CONSTRUCTION, 2020, 50(8): 27-31,71. doi: 10.13204/j.gyjzG20052507
[10]	Yang Jianjiang Liu Ye Li Suyan Wang Fei Liu Ping, . EXPERIMENTAL RESEARCH ON WIND AND SHEAR RESISTANCE OF CONTAINER HOUSE SIDING[J]. INDUSTRIAL CONSTRUCTION, 2015, 45(7): 164-169. doi: 10.13204/j.gyjz201507033
[11]	Pang Rui, Zhao Yi, Liang Shuting, Zhang Shuo. EXPERIMENTAL STUDY OF SHEAR CAPACITY OF HAIRPIN SLAB CONNECTION IN PRECAST RC FLOOR[J]. INDUSTRIAL CONSTRUCTION, 2014, 44(02): 50-54. doi: 10.13204/j.gyjz201402012
[12]	Pang Rui, Xiong Xiaoli, Jiang Lifeng. EXPERIMENTAL STUDY OF SHEAR CAPACITY OF π-SHAPE SLAB JOINTS IN PRECAST RC DIAPHRAGM[J]. INDUSTRIAL CONSTRUCTION, 2014, 44(08): 84-87.
[13]	Chai Zhenling, Guo Zixiong, Hu Yidong, Li Gang, Yin Tinghua. EXPERIMENTAL RESEARCH ON SHEAR BEHAVIOR OF STONE MASONRY JOINT UNDER SHEAR AND COMPRESSION LOADING[J]. INDUSTRIAL CONSTRUCTION, 2011, 41(9): 63-66. doi: 10.13204/j.gyjz201109014
[14]	Pang Rui, Liang Shuting, Zhu Xiaojun, Wu Chuanchuan, Meng Yao. EFFECT OF DETAILED FORMATIONS ON THE PLANE SHEAR MECHANICAL PROPERTY OF HAIRPIN CONNECTORS IN PRECAST RC FLOOR SLABS[J]. INDUSTRIAL CONSTRUCTION, 2011, 41(6): 79-83. doi: 10.13204/j.gyjz201106017
[15]	Zhao Ruirong, Chen Lin, Zhou Yun. SHEAR PERFORMANCE ANALYSIS OF STIFFENED STEEL PLATE SHEAR WALLS WITH SLITS[J]. INDUSTRIAL CONSTRUCTION, 2010, 40(5): 119-123. doi: 10.13204/j.gyjz201005025
[16]	Huang Hua, Liu Boquan, Liu Weiduo. STUDY ON SHEAR BOND PERFORMANCE BETWEEN POLYMER MORTAR AND CONCRETE[J]. INDUSTRIAL CONSTRUCTION, 2009, 39(4): 103-105. doi: 10.13204/j.gyjz200904023
[17]	Liu Jun, Li Yingmei, Li Qing. EXPERIMENTAL STUDY ON INTERFACIAL SHEARING PROPERTY OF FRP REINFORCED CONCRETE[J]. INDUSTRIAL CONSTRUCTION, 2008, 38(11): 79-81,96. doi: 10.13204/j.gyjz200811019
[18]	Wen Baojun, Liang Xingwen, Hou Lina. RESEARCH ON SHEAR CAPACITY OF YIELD HINGE REGIONS OF REINFORCED CONCRETE SHEAR WALL[J]. INDUSTRIAL CONSTRUCTION, 2008, 38(12): 60-64. doi: 10.13204/j.gyjz200812016
[19]	Li Junhua, Wang Xintang, Xue Jianyang, Zhao Hongtie. EXPERIMENT AND ANALYSIS ON SHEAR PERFORMANCE OF STEEL REINFORCED HIGH - STRENGTH CONCRETE COLUMNS[J]. INDUSTRIAL CONSTRUCTION, 2007, 37(3): 90-94,59. doi: 10.13204/j.gyjz200703022
[20]	Yang Yongxin, Cao Jinsong, Yue Qingrui, Zhao Yan, Cai Peng, Peng Fuming, Li Qingwei. STANDARD MOULD ON SHEAR SPECIMEN OF RESIN[J]. INDUSTRIAL CONSTRUCTION, 2005, 35(8): 5-6,4. doi: 10.13204/j.gyjz200508002

Supplements(0)

Cited By

Cited by

Periodical cited type(4)

1.	廖菲菲，徐理，张玉清. 低温下装配式建筑层间结构脆弱点检测与仿真. 计算机仿真. 2024(08): 326-330 .
2.	孟宪宏，宋正泉，费小爽，陈建华. 预制混凝土夹心保温墙板连接件抗扭性能试验. 沈阳建筑大学学报(自然科学版). 2024(06): 994-1000 .
3.	张轶琛，陈国新，郭孟攀，刘健. 竖向荷载下夹心保温复合墙板片状金属拉结件承载力计算方法研究. 石河子大学学报(自然科学版). 2024(06): 692-701 .
4.	涂娈芳，秦晓豪. 预制夹心保温墙板正打工艺的研究与工程实践. 城市建筑. 2023(02): 164-166 .

Other cited types(6)

Proportional views

Proportional views

通讯作者: 陈斌, bchen63@163.com

1.
沈阳化工大学材料科学与工程学院沈阳 110142

Get Citation

PDF

XML

Article Metrics

Article views (232) PDF downloads(119)