EFFECTS OF LAYERS AND FLOOR HEIGHT ON QUANTITY OF SHEAR WALLS IN TALL BUILDINGS

Hu Kongpeng; Chen Daozheng

doi:10.13204/j.gyjz201303014

Volume 43 Issue 3

Dec. 2014

Turn off MathJax

Article Contents

Abstract

References

Article Navigation > INDUSTRIAL CONSTRUCTION > 2013 > 43(3): 67-70

LYU Zhilin, JIANG Xu, QIANG Xuhong, SUN Kai, DONG Hao. Feasibility Research on Strengthening Damaged Steel Structure with Self-Stress SMA[J]. INDUSTRIAL CONSTRUCTION, 2022, 52(6): 174-182. doi: 10.13204/j.gyjzG20100301

Citation:

Hu Kongpeng, Chen Daozheng. EFFECTS OF LAYERS AND FLOOR HEIGHT ON QUANTITY OF SHEAR WALLS IN TALL BUILDINGS[J]. INDUSTRIAL CONSTRUCTION, 2013, 43(3): 67-70. doi: 10.13204/j.gyjz201303014

Citation:

Hu Kongpeng, Chen Daozheng. EFFECTS OF LAYERS AND FLOOR HEIGHT ON QUANTITY OF SHEAR WALLS IN TALL BUILDINGS[J]. INDUSTRIAL CONSTRUCTION, 2013, 43(3): 67-70. doi: 10.13204/j.gyjz201303014

PDF( 0 KB)

EFFECTS OF LAYERS AND FLOOR HEIGHT ON QUANTITY OF SHEAR WALLS IN TALL BUILDINGS

doi: 10.13204/j.gyjz201303014

1.
School of Civil Engineering,Hefei University of Technology,Hefei 230009,China

Received Date: 2012-03-22
Publish Date: 2013-03-20

Abstract

Abstract

Based on the calculation and analysis of engineering examples by finite element structural software SATWE it was studied effects of layers and floor height in tall shear walls structure on quantity of shear walls,and obtained some reference suggestions.Usually when the design of tall shear walls structure it is tried to make the ratio of height to width being not greater than 4,which can control the cost of a building.The change of floor height has more significant impact than the change of layers in rigidity of shear-wall structure.When increasing the wall thickness of shear-wall to ensure the max-story drift under the same conditions,the increase in layers and floor height of structure will produce adverse effects on the overall stability and safety of the structure.
- shear walls structure,
- floor height,
- wall thickness,
- story drift,
- the ratio of stiffness to weight

FullText(HTML)

References(6)

References

[2] GB 500112010建筑抗震设计规范[S].

JGJ 32010高层建筑混凝土结构技术规程[S].

[3] 包世华.新编高层建筑结构[M].北京:中国水利水电出版社,2001:46－68.

[4] 高层建筑结构空间有限元分析与设计软件 SATWE[R].北京:中国建筑科学研究 PKPMCAD 工程部,2003.

[5] 王月华.七度区高层剪力墙数量优化研究[D].青岛:中国石油大学,2004.

[6] 韦承基,刘经伟.高层建筑层间位移控制建议[J].工程抗震,1994(2):1－3.

Relative Articles

[1]	WANG Congying, KOU Xianqin, LU Xiaoyan, FAN Jiansheng, LIU Yufei. Research on Dynamic Performance Changes of Shear Wall Structures Before and After Cracking Damage[J]. INDUSTRIAL CONSTRUCTION, 2025, 55(1): 13-19. doi: 10.3724/j.gyjzG23121403
[2]	LIU Chengqing, XU Dibing, ZHANG Huaxin. Seismic Strengthening Design and Analysis of a Boiler Steel Frame[J]. INDUSTRIAL CONSTRUCTION, 2024, 54(3): 237-245. doi: 10.13204/j.gyjzG22050603
[4]	Zhu Zhijun Zhang Qing Tan Yongqiang Zhou Xiangjiang, . RESEARCH ON EQUIVALENT ANALYSIS OF TRUSS BEAMS OF PREFABRICATED STEEL FRAME STRUCTURE WITH DIAGONAL BRACING JOINTS[J]. INDUSTRIAL CONSTRUCTION, 2015, 45(10): 24-30. doi: 10.13204/j.gyjz201510005
[5]	Song Xiaolu, Qian Jiaru, Feng Baochun, Zhang Yichao. TEST STUDY ON SEISMIC BEHAVIOR OF SPＲAYED CONCＲETE SANDWICH SHEAR WALLS WITH LOW SHEAR-SPAN RATIO[J]. INDUSTRIAL CONSTRUCTION, 2014, 44(07): 16-20.
[6]	Liu Jianmin, Sun Bing, He Jie. STUDY OF SEISMIC PERFORMANCE OF SHEAR WALL STURCTURE CONSIDERING THE EFFECT OF DIFFERENT SET OF CONSTRUCTION JOINTS[J]. INDUSTRIAL CONSTRUCTION, 2014, 44(02): 64-68. doi: 10.13204/j.gyjz201402015
[7]	Yuan Kang, Li Yingmin, Zhang Songbai. STUDY OF UNIDIRECTIONAL WALL FRAMES' INFLUENCE ON THE SEISMIC PERFORMANCE OF SHEAR WALL STRUCTURE[J]. INDUSTRIAL CONSTRUCTION, 2014, 44(07): 37-41.
[8]	Li Junfeng, Xu Yan, Yang Xiaodong. OPTIMIZATION DESIGN OF HIGH-RISE SHEAR WALL STRUCTURE WITH STAGGERED STORIES[J]. INDUSTRIAL CONSTRUCTION, 2012, 42(12): 151-155. doi: 10.13204/j.gyjz201212033
[9]	Li Xiaolei, Li Qingning, Zhang Pinle. REASERCH ON AXIAL COMPRESSION RATIO OF SHORT-LIMB SHEAR WALLS[J]. INDUSTRIAL CONSTRUCTION, 2011, 41(3): 73-75,120. doi: 10.13204/j.gyjz201103014
[10]	Zhang Xuewei, Liu Weidong, Zhang Li, Zhao Yan, Yan Yinkun. RENOVATION AND REINFORCEMENT DESIGN OF A FRAMED OFFICE BUILDING[J]. INDUSTRIAL CONSTRUCTION, 2011, 41(2): 123-126,122. doi: 10.13204/j.gyjz201102028
[11]	Liu Yan, Huang Liang, Zhou Jing. CONSIDERATIONS ON "CODE FOR DESIGN OF MASONRY STRUCTURES"[J]. INDUSTRIAL CONSTRUCTION, 2011, 41(1): 136-138. doi: 10.13204/j.gyjz201101030
[12]	Li Bing, Li Hongnan. RESEARCH ON QUASI-STATIC TEST OF REINFORCED CONCRETE SHEAR WALLS WITH DIFFERENT SHEAR-SPAN RATIO[J]. INDUSTRIAL CONSTRUCTION, 2010, 40(9): 32-36. doi: 10.13204/j.gyjz201009011
[13]	Liang Xingwen, Yang Penghui, Deng Mingke. THE STUDY ON THE ALLOWABLE AXIAL LOAD RATIO OF CONCRETE SHEAR WALL WITHOUT CONFINED BOUNDARY ELEMENTS[J]. INDUSTRIAL CONSTRUCTION, 2009, 39(9): 67-70. doi: 10.13204/j.gyjz200909013
[14]	Liu Lin, Bai Guoliang, Li Xiaowen, Li Hongxing, Zhao Chunlian. DISPLACEMENT-BASED SEISMIC DESIGN METHOD OF RC FRAMES[J]. INDUSTRIAL CONSTRUCTION, 2009, 39(5): 1-5. doi: 10.13204/j.gyjz200905001
[15]	Liu Xiaofan, Tong Yuesheng. STORY SIDESWAY STIFFNESS OF SHEAR WALL IN REINFORCED CONCRETE STRUCTURES[J]. INDUSTRIAL CONSTRUCTION, 2009, 39(4): 49-53. doi: 10.13204/j.gyjz200904012
[16]	Yang Qiwei, Liang Xingwen, Jiang Jian. RESEARCH ON DISPLACEMENT-BASED SEISMIC DESIGN METHOD OF REINFORCED CONCRETE FRAME-SHEAR WALL STRUCTURES[J]. INDUSTRIAL CONSTRUCTION, 2007, 37(2): 1-5. doi: 10.13204/j.gyjz200702001
[17]	Chang Linrun. DISCUSSION ON SEVERAL PROBLEMS OF COUPLING WALL-BEAMANTI-EARTHQUAKE DESIGN OF TALL SHEAR WALL STRUCTURE[J]. INDUSTRIAL CONSTRUCTION, 2007, 37(2): 28-31,36. doi: 10.13204/j.gyjz200702007

Supplements(0)

Cited By

Cited by

Periodical cited type(2)

1.	邓劼，张清现. 基于“两山理论”下的旅游城市废弃矿山开发利用研究——以桂林市临桂新区相思江流域废弃矿山为例. 城市建设理论研究(电子版). 2024(13): 4-6 .
2.	杨剑飞，张浩轩. 盐业遗址文创开发的国际经验与路径探析. 盐业史研究. 2023(04): 65-72 .

Other cited types(0)

Proportional views

Proportional views

通讯作者: 陈斌, bchen63@163.com

1.
沈阳化工大学材料科学与工程学院沈阳 110142

Get Citation

PDF

XML

Article Metrics

Article views (92) PDF downloads(70)