装配式钢-薄层超高性能混凝土组合梁大直径群钉连接件抗剪性能数值分析

陈阳; 宁建; 任重; 杨勇

doi:10.13204/j.gyjzG23070905

装配式钢-薄层超高性能混凝土组合梁大直径群钉连接件抗剪性能数值分析

doi: 10.13204/j.gyjzG23070905

陈阳^1,2,
宁建¹,
任重¹,
杨勇²

1. 上海大学力学与工程科学学院, 上海 200444;
2. 绿色建筑全国重点实验室, 西安建筑科技大学, 西安 710055

基金项目:

国家自然科学基金项目（52108156）；绿色建筑全国重点实验室开放基金项目（LSKF202215）。

详细信息

作者简介:
陈阳,女,1992年出生,博士,讲师。电子信箱:xauatchenyang@126.com

计量
- 文章访问数: 53
- HTML全文浏览量: 6
- PDF下载量: 0
- 被引次数: 0
出版历程
- 收稿日期: 2023-07-09
- 网络出版日期: 2024-02-28

Numerical Study on Shear Performance of Grouped Large Headed Stud Connectors in Prefabricated Steel-Thin UHPC Composite Girder

1. School of Mechanics and Engineering Sciences, Shanghai University, Shanghai 200444, China;
2. State Key Laboratory of Green Building, Xi'an University of Architecture & Technology, Xi'an 710055, China

摘要

摘要: 为研究大直径群钉连接件在装配式钢-薄层超高性能混凝土组合梁桥中的抗剪性能，通过有限元软件ABAQUS建立了19个推出试件模型。着重分析了浇筑方式、栓钉间距、键群间距和键群数量对试件抗剪承载力、抗剪刚度和荷载-滑移曲线的影响规律。研究结果表明：试件破坏模式主要表现为栓钉根部的剪断以及混凝土的局部压碎；使用预制超高性能混凝土板推出试件的抗剪承载力比现浇试件降低10%以内；栓钉间距小于2.5倍栓钉直径时，试件抗剪承载力明显下降；随着键群间距和数量的增加，键群中单个栓钉的抗剪承载力以及抗剪刚度减小。针对装配式钢-薄层超高性能混凝土大直径群钉连接件提出了预测其荷载-滑移关系的理论模型，并将抗剪承载力试验结果与规范计算结果进行了比较，得到了适用于装配式钢-薄层超高性能混凝土组合梁桥大直径群钉连接件的计算方法。
- 装配式结构 /
- 大直径群钉连接件 /
- 超高性能混凝土薄板 /
- 抗剪性能 /
- 有限元
Abstract: In order to study the shear performance of grouped large headed stud connectors in prefabricated steel-thin UHPC composite girder, 19 push-out specimens were established by finite element software ABAQUS to study the influence of casting method, stud spacing, key group spacing, and key group number on the shear bearing capacity, shear stiffness, and load-slip curve of the specimens. The results showed that the failure mode of specimens was mainly the shear failure at the root of studs and the local crushing of concrete slabs. The shear bearing capacity of prefabricated specimens was reduced by 10% compared with the cast-in-place specimens. The shear bearing capacity of the specimens decreased significantly when the spacing of studs was less than 2.5 times the diameter of studs. The shear bearing capacity and shear stiffness of individual stud in the key group were reduced by the increase of the spacing and number of key groups. The theoretical model for predicting the load-slip relation of the prefabricated steel-thin UHPC grouped large headed stud connectors was proposed. Moreover, the results of the shear capacity from ABAQUS were compared with the calculated results from the code, and a design method for prefabricated steel-thin UHPC composite girder bridge grouped large headed stud connectors was obtained.
- prefabricated structure /
- grouped large headed stud connectors /
- thin UHPC slab /
- shear performance /
- finite element

HTML全文

参考文献(26)

[1]	聂建国, 刘明, 叶列平. 钢-混凝土组合结构[M]. 北京:中国建筑工业出版社, 2005.
[2]	VIEST I M. Investigation of stud shear connectors for composite concrete and steel T beams[J]. Journal of the American Concrete Institute, 1956, 27(8):875-891.
[3]	VIEST I M. Review of research on composite steel-concrete beams[J]. American Society of Civil Engineers, 1961, 126(2):1101-1121.
[4]	OKADA J, YODA T. Influence of stud size and stud strength of smaller spaced grouped arrangement of headed stud connectors on shear strength behavior and evaluation of shear strength of slabs[J]. Doboku Gakkai Ronbunshuu A, 2006, 62(3):556-559.
[5]	苏庆田, 李雨. 高强度砂浆群钉连接件抗剪承载力试验[J]. 同济大学学报(自然科学版), 2015, 43(5):699-705.
[6]	WANG Y H, YU J, LIU J P, et al. Shear behavior of shear stud groups in precast concrete decks[J]. Engineering Structures, 2019, 187:73-84.
[7]	魏振. 预制装配式钢-混凝土组合梁栓钉抗剪连接件推出试验研究[D]. 厦门:华侨大学, 2019.
[8]	韦建刚, 罗霞, 陈宝春, 等. 圆高强钢管UHPC梁抗弯性能研究[J]. 工程力学, 2021, 38(1):183-194.
[9]	邵旭东, 胡伟业, 邱明红, 等. 组合梁负弯矩区UHPC接缝抗弯性能试验研究[J]. 中国公路学报, 2021, 34(8):246-260.
[10]	樊健生, 王哲, 杨松, 等. 钢-超高性能混凝土组合箱梁弹性弯曲性能试验研究及解析解[J]. 工程力学, 2020, 37(11):36-46.
[11]	邵旭东, 曹君辉, 易笃韬, 等. 正交异性钢板-薄层RPC组合桥面基本性能研究[J]. 中国公路学报, 2012, 25(2):40-45.
[12]	CAO J H, SHAO X D, DENG L, et al. Static and fatigue behavior of short-headed studs embedded in a thin ultrahigh-performance concrete layer[J]. Journal of Bridge Engineering, 2017, 22(5):1-16.
[13]	谢宏伟. 钢-超高性能混凝土组合结构大直径栓钉的抗剪性能研究[D]. 成都:西南交通大学, 2019.
[14]	XU C, SUGIURA K, WU C, et al. Parametrical static analysis on group studs with typical push-out tests[J]. Journal of Constructional Steel Research, 2012, 72(5):84-96.
[15]	SHIM C S, KIM D W. Design Code on Stud Shear Connectors for New Details[C]//Composite Construction in Steel and Concrete VII. 2016:703-711.
[16]	中华人民共和国住房和城乡建设部.钢-混凝土组合桥梁设计规范:GB 50917-2013[S]. 北京:中国标准出版社, 2013.
[17]	中华人民共和国交通运输部.公路钢结构桥梁设计规范:JTG D64-2015[S]. 北京:人民交通出版社, 2015.
[18]	李昊煜. RPC材料的塑性损伤本构模型参数识别及有限元验证[D]. 北京:北京交通大学, 2009.
[19]	WANG J Q, XU Q Z, YAO Y M, et al. Static behavior of grouped large headed stud-UHPC shear connectors in composite structures[J]. Composite Structures, 2018, 206(12):202-214.
[20]	XUE W C, DING M, WANG H, et al. Static behavior and theoretical model of stud shear connectors[J]. Journal of Bridge Engineering, 2008, 13(6):623-634.
[21]	SU Q T, YANG G, BRADFORD M A. Static behaviour of multi-row stud shear connectors in high-strength concrete[J]. Steel and Composite Structures, 2014, 17(6):967-980.
[22]	DING J N, ZHU J S, KANG J F, et al. Experimental study on grouped stud shear connectors in precast steel-UHPC composite bridge[J/OL]. Engineering Structures, 2021, 242(1)[2021-09-01].https://doi.org/10.1016/j.engstruct.2021.112479.
[23]	刘沐宇, 李苏, 张强. 集束式长短剪力钉抗剪性能参数影响研究[J]. 华中科技大学学报(自然科学版), 2019, 47(7):19-23.
[24]	ECS. Design of composite steel and concrete structure:EN 1994-Eurocode 4[S]. England:European Committee for Standardization, 1994.
[25]	AASHTO LRFD. Bridge design specification:AASHTO LRFD[S]. Washington D C:Amercian Association of State Highway and Transportation Officials, 2007.
[26]	JSCE. Standard specification for steel and composite structures[S]. Japan:Japan Society of Civil Engineers, 2007.