采用高强度螺栓连接件的钢-混凝土组合梁力学性能研究

盛永军

doi:10.13204/j.gyjzG21061514

采用高强度螺栓连接件的钢-混凝土组合梁力学性能研究

doi: 10.13204/j.gyjzG21061514

盛永军

浙江交工集团股份有限公司, 杭州 310051

基金项目:

住房和城乡建设部科技项目（2019-K-086）。

详细信息

作者简介:
盛永军,男,1974年出生,高级工程师。电子信箱:493689539@qq.com

计量
- 文章访问数: 178
- HTML全文浏览量: 13
- PDF下载量: 1
- 被引次数: 0
出版历程
- 收稿日期: 2021-06-15
- 网络出版日期: 2022-01-11

RESEARCH ON MECHANICAL PROPERTIES OF STEEL-CONCRETE COMPOSITE BEAMS WITH HIGH-STRENGTH BOLT CONNECTORS

SHENG Yongjun

Zhejiang Jiaogong International Engineering Co., Ltd., Hangzhou 310051, China

摘要

摘要: 为研究高强度螺栓作为抗剪连接件的钢-混凝土组合梁力学性能，通过改变高强螺栓的布置间距，对4根组合梁试件进行单点静力加载。由试验得到荷载-挠度曲线、荷载-滑移曲线和沿截面高度的应变分布曲线，进而分析端部螺栓间距和预紧力两个变量对组合梁抗弯承载力、初始刚度、横截面应变分布的影响。试验结果表明：集中荷载作用下，试验梁为典型弯曲破坏；减小端部螺栓布置间距可以提高组合梁的承载力及初始刚度；而提高预紧力也可提高组合梁初始刚度，但对极限承载力影响较小。
- 高强螺栓连接件 /
- 钢-混凝土组合梁 /
- 荷载-滑移曲线 /
- 承载力 /
- 初始刚度
Abstract: In order to study the mechanical properties of steel-concrete composite beams with high-strength bolt connectors, single-point static loading was conducted on 4 composite beam specimens by changing the pre-tightening forces of high-strength bolts and the spacing of end bolts. The load-deflection curve, the load-slip curve and the strain curve along the height of the section were obtained from the experiment, and then the influence of the two variables on the flexural bearing capacity, initial stiffness and cross-sectional strain of the composite beam was analyzed. The test results showed that the test beam subjected to concentrated loads was typical bending failure, reducing the spacing of the end bolts could improve the bearing capacity and initial stiffness of the composite beam and increasing the pre-tightening force could also increase the initial stiffness of the composite beam, but had little effect on the ultimate bearing capacity.
- high-strength bolt connector /
- steel-concrete composite beam /
- load-slip curve /
- bearing capacity /
- initial stiffness

HTML全文

参考文献(15)

[1]	赵伟,张征文. 钢结构桥梁[M].北京:人民交通出版社, 2015.
[2]	马莹,宋伟豪,王潇,等.基于公路规范的钢-GFRP-混凝土组合梁桥受力性能分析[J].中外公路,2020,40(6):83-87.
[3]	严鑫,陈驹.新型可替换式组合梁连接件剪切刚度研究[J].低温建筑技术, 2019, 41(1):14-18.
[4]	刘中良.装配式组合梁高强螺栓连接件抗剪性能试验研究[D].湘潭:湘潭大学, 2017.
[5]	龚志刚,党志杰.用高强度螺栓作为结合梁桥的剪力连接件[J].世界桥梁,2003(2):56-63.
[6]	KWON G, ENGELHARDT M D, KLINGNER R E. Strengthening Existing Non-Composite Steel Girder Bridges by the Use of Post-Installed Shear Connectors[J]. IABSE Congress Report, 2008, 17(19):198-199.
[7]	KWON G, ENGELHARDT M D, KLINGNER R E. Behavior of Post-Installed Shear Connectors Under Static and Fatigue Loading[J]. Steel Construction, 2010, 66(4):532-541.
[8]	KWON G, ENGELHARDT M D, KLINGNER R E. Experimental Behavior of Bridge Beams Retrofitted with Post-Installed Shear Connectors[J]. Journal of Bridge Engineering, 2011, 16(4):536-545.
[9]	LIU X P, MARK B A, CHEN Q J. Finite Element Modelling of Steel-Concrete Composite Beams with High-Strength Friction-Grip Bolt Shear Connectors[J]. Finite Elements in Analysis and Design, 2016,108:54-65.
[10]	ATAEI A, BRADFORD M A, LIU X. Experimental Study of Composite Beams Having a Precast Geopolymer Concrete Slab and Deconstructable Bolted Shear Connectors[J]. Engineering Structures, 2016, 114(1):1-13.
[11]	LIU X, BRADFORD M A, ATAEI A. Flexural Performance of Innovative Sustainable Composite Steel-Concrete Beams[J]. Engineering Structures, 2017, 130(1):282-296.
[12]	ZHANG Y J, CHEN B, LIU A, et al. Experimental Study on Shear Behavior of High Strength Bolt Connection in Prefabricated Steel-Concrete Composite Beam[J]. Composites Part B:Engineering, 2019, 159(15):481-489.
[13]	张勇,袁波,王健康.新型装配式螺栓连接件极限承载力研究[J].贵州大学学报(自然科学版),2019,36(1):112-117.
[14]	ZHAO W, LU S Q, JING X Y. Shear Performance of High-Strength Bolt Connector Considering Different Pad and Bolt Hole[J]. Structures,2020,28(10):1219-1230.
[15]	中华人民共和国住房和城乡建设部. 金属材料拉伸试验第1部分:室温试验方法:GB/T 228.1-2010[S]. 北京:中国标准出版社, 2017.