登录
注册
E-alert
登录
注册
E-alert
RESEARCH ON WORKING STRESS OF STEEL STRUCTURES BY HOLE-DRILLING METHOD
-
摘要: 通过有限元方法对盲孔法释放系数A、B进行标定，并与轴心受拉下标定试验的结果进行对比验证。结果表明：对于轴心受拉构件，使用盲孔法进行工作应力的检测是可行的；有限元标定得到的释放系数A、B在低应力状态下与实测值吻合较好；对于高应力状态下的孔边塑性应变引发的误差，可根据形状改变比能参量S与释放系数A、B的关系进行修正；对于加载状态下钻孔时产生的切削加工应变，可根据试验测得的切削加工应变与释放应变的关系进行修正。Abstract: The finite element method was used to calibrate the release coefficient A and B of the hole-drilling method, and the results were compared with the test results under axial tension load. The results showed that it was feasible to use hole-drilling method to detect the working stress of axial tension member. The release coefficient A and B obtained by finite element calibration were in good agreement with the measured value under low stress state. The error caused by the plastic strain on the hole edge under high stress state could be modified according to the relationship between the distortion-energy parameter S and the release coefficient A and B. The cutting strain produced by drilling under loading state could be modified according to the measured relationship between the cutting strain and the released strain.
-
Key words:
- hole-drilling method /
- release coefficient /
- finite element /
- plastic strain /
- cutting strain
-
American Society of Testing Materials. Standard Test Method for Determining Residual Stresses by the Hole-Drilling Strain-Gage Method:ASTM E837-81[S].PA:ASTM International,2008. 中国船舶工业总公司.残余应力测试方法:钻孔应变释放法:CB 3395-92[S].北京:中国船舶集团公司综合研究所,1992. 翟传明,邸小坛,白伟亮,等.盲孔法检测既有金属结构应力的研究[J].建筑科学,2011,27(增刊1):116-121. 赵海燕,斐怡,史耀武,等.用小孔释放法测量焊接高残余应力时孔边塑性变形对测量精度的影响及修正方法[J].机械强度,1996,18(3):17-20. 王龙,吴波.盲孔法识别拉(压)弯钢管内力的分析与试验[J].东南大学学报,2009,39(6):1180-1186. 曾宏,盛国赛,谢晓锋,等.盲孔法测量钢结构工作应力试验研究[J].广东土木与建筑,2006(4):48-51. 李伟,王文欣,李林安,等.钻孔法检测大型钢结构工作应力的研究[J].佳木斯大学学报, 2015,33(4):524-527. 陈怀宁,陈亮山,董秀中.盲孔法测量残余应力的钻削加工应变[J]. 焊接学报,1994,15(4):276-280. -
点击查看大图
计量
- 文章访问数: 178
- HTML全文浏览量: 7
- PDF下载量: 0
- 被引次数: 0
下载:
