不锈钢芯板一字形墙轴心受压承载力研究

陈大川; 蒋玉春; 舒兴平; 谭永强

doi:10.13204/j.gyjz202002008

不锈钢芯板一字形墙轴心受压承载力研究

doi: 10.13204/j.gyjz202002008

1. 湖南大学土木工程学院, 长沙 410082;
2. 远大可建科技有限公司, 湖南岳阳 414600

详细信息

作者简介:
陈大川,男,1967年出生,博士,教授,研究生导师。电子信箱:1461791566@qq.com

计量
- 文章访问数: 72
- HTML全文浏览量: 15
- PDF下载量: 3
- 被引次数: 0
出版历程
- 收稿日期: 2019-06-20

RESEARCH ON THE BEARING CAPACITY OF THE IN-LINE WALL OF THE STRUCTURE OF STAINLESS STEEL SANDWICH PANEL UNDER AXIAL COMPRESSION

1. College of Civil Engineering, Hunan University, Changsha 410082, China;
2. Broad Sustainable Built Technology Co., Ltd., Yueyang 414600, China

摘要

摘要: 不锈钢芯板一字形墙是由两块不锈钢面板和正交均匀排布的不锈钢芯管组成的一字形截面构件，芯管与面板的连接采用铜钎焊焊接。主要研究不锈钢芯板一字形墙轴心受压时的承载能力，提出了其轴压承载力的计算公式。首先，进行了有限元特征值屈曲分析，得到了计算一字形墙弹性屈曲荷载及相应的正则化高宽比λ_n的算式；通过非线性有限元分析，对面板厚度、高宽比、芯管外径、芯管壁厚以及芯管分布间距等参数变化对不锈钢芯板一字形墙轴压承载力的影响进行分析，得到了轴心受压稳定系数φ，以及进行稳定设计的φ-λ_n曲线；设计了3组不锈钢芯板一字形墙试件，并对其轴压承载力进行了试验研究。试验结果、有限元分析结果和计算结果吻合较好，验证了不锈钢芯板一字形墙轴压承载力计算式的安全性。
- 不锈钢芯板 /
- 一字形截面 /
- 轴心受压 /
- 承载力设计
Abstract: The in-line wall of the structure of stainless steel sandwich panel is a cross-shaped member composed of two stainless steel panels and orthogonally arranged stainless steel core tube. The connection between the core tube and the panel is brazed by copper. In the paper, the bearing capacity of in-line wall of stainless steel sandwich panel under axial compression was studied, and the calculation formula of the bearing capacity under axial compression was proposed. Firstly, the finite element eigenvalue buckling analysis was carried out, and the formula for calculating the elastic buckling load of the wall and the corresponding regularized aspect ratio λ_n was obtained. Through the finite element non-linear analysis, the influence of the thickness of the panel, the aspect ratio, the outer diameter of the core tube, the wall thickness of the core tube and the distribution distance of the core tube on the bearing capacity of the axially compressed in-line wall of stainless steel sandwich panel was analyzed, and the stability coefficient φ of the axial compression was obtained, as well as φ-λ_n curve of stability by design; three sets of the in-line wall of specimens stainless steel sandwich panel were designed, and the axial compressive bearing capacity was tested. The test results, finite element analysis results and design formulas were in good agreement. The safety of the calculation formula for the axial compressive bearing capacity of the in-line wall of the structure of stainless steel sandwich panel were verified.
- the structure of stainless steel sandwich panel /
- in-line section /
- axial compression /
- design of bearing capacity

HTML全文

参考文献(16)

王海忠,何保康,陶忠.建筑夹芯板结构性能分析[J].钢结构, 1999,15(4):41-45.

王海忠,赵天宇.夹芯板结构设计与破坏模式分析[J].工业建筑,2005,35(8):97-99

,120.

彭明军. 钎焊蜂窝铝板力学性能研究[D]. 昆明:昆明理工大学, 2013.

POKHAREL N, MAHENDRAN M. Finite Element Analysis and Design of Sandwich Panels Subject to Local Buckling Effects[J]. Thin-Walled Structures, 2004, 42(4):589-611.

PAIK J K, THAYAMBALLI A K, KIM G S. The Strength Charac-teristics of Aluminum Honeycomb Sandwich Panels[J]. Thin-Walled Structures, 1999, 35(3):205-231.

周祝林. 蜂窝夹层板的极限强度[J].力学学报,1993(1):62-69.

韦芳芳,郑泽军,喻君,等.基于钢板屈曲分析的双钢板-混凝土组合剪力墙轴压承载力计算方法[J].工程力学,2019, 36(2):154-164.

朱梓健,李俞瑜,魏木旺,等.新型装配式钢板组合剪力墙轴压受力性能分析[J].钢结构,2018,33(11):87-91.

郝婷玥,曹万林,张建伟,等.内置加劲肋钢板-混凝土组合剪力墙轴压性能研究[J].建筑结构学报,2017,38(增刊1):90-97.

中国国家标准化管理委员会. 夹层结构侧压性能试验方法:GB/T 1454-2005[S]. 北京:中国标准出版社,2005.

TIMOSHENKO S P, WOINOWSKY-KRIEGER S. Theory of Plates and Shells[M]. New York:McGraw-Hill, 1959.

TIMOSHENKO S P, GERE J M. Theory of Elastic Stability[M]. New York:McGraw-Hill, 1961

TONG J Z, GUO Y L. Shear Resistance of Stiffened Steel Corrugated Shear Walls[J]. Thin-Walled Structures, 2018,127:76-89.

GUO Y, ZHU J, WANG M, et al. Overall Instability Performance of Concrete-Infilled Double Steel Corrugated-Plate Wall[J].Thin-Walled Structures, 2018, 130:372-394.

ZHU J S, GUO Y L, ZHU B L, et al. Strength Design of Concrete-Infilled Double Steel Corrugated-Plate Walls Under Uniform Compressions[J]. Thin-Walled Structure, 2019,141:153-174.

WANG M Z, GUO Y L, ZHU J S, et al. Strength Design of Concrete-Infilled Double Steel Corrugated-Plate Walls with T-Section Under Combined Axial Compression and Bending Moment[J]. J. of Constructional Steel Research, 2019, 160:23-44.

施引文献

资源附件(0)

访问统计