不锈钢轴心受压构件稳定承载能力计算方法研究

舒赣平; 郑宝锋; 沈晓明

doi:10.13204/j.gyjz2011205003

不锈钢轴心受压构件稳定承载能力计算方法研究

doi: 10.13204/j.gyjz2011205003

1.
1. 东南大学土木工程学院南京 210096;
2.
2. 苏州工业园区设计研究院有限责任公司江苏苏州 215020

基金项目:

江苏省自然科学基金资助项目(BK2009287);国家自然科学基金资助项目(51178098)

详细信息

作者简介:
舒赣平，男，1964年出生，教授，博士生导师。

中图分类号: TU391;TU311.4
计量
- 文章访问数: 90
- HTML全文浏览量: 7
- PDF下载量: 99
- 被引次数: 0
出版历程
- 收稿日期: 2011-10-20
- 刊出日期: 2012-05-20

NEW DESIGN METHOD FOR STAINLESS STEEL COLD- FORMED TUBULAR COLUMNS UNDER AXIAL LOAD

1.
1. College of Civil Engineering,Southeast University,Nanjing 210096,China;
2.
2. Suzhou Industrial Park Design &Research Institute,Suzhou 215020,China

摘要

摘要: 国内外不锈钢材料力学性能的试验资料表明:不同牌号不锈钢材料的力学性能差别较大;同牌号不锈钢材料的力学性能也有一定差别,而材料力学性能变化对轴心受压不锈钢柱的稳定性系数的影响在国外典型不锈钢结构设计规范中均无明确的规定。基于经验证的有限元模型,计算了30种典型不锈钢材料的稳定系数曲线,采用修正正则化长细比概念对Perry公式及KR公式进行改进,得到适用于常用不锈钢材料力学性能的轴心受压柱稳定系数表达式,并与国内外已有的试验数据进行对比,结果表明,此表达式具有较高的精度,可供我国不锈钢结构设计规程中轴心受压构件设计条文编制参考。
- 不锈钢 /
- 冷成型管材 /
- 轴心受压长柱 /
- 计算方法
Abstract: Test results of the stainless steel material property indicate that: considerable difference exists among different states of the same type stainless steel and also exists among varieties of type.However this difference is not directly considered in the typical design codes existing in the world.Based on the verified FEM model,total 30 column curves are calculated that covered the range of material properties in common use.The concept of modification slenderness ratio is utilized to modify the Perry formula and the K＆R formula; at last,new design formula is obtained for calculating the buckling strength of stainless steel columns.Comparisons between the available test result and the proposed approach are conducted.The comparisons indicated that the proposed approach could fit the test results well.This approach could be used as a reference for the first version of stainless steel design code of China．
- stainless steel /
- cold-formed tubular member /
- long columns under axial load /
- design method

HTML全文

参考文献(19)

EC3. Eurocode 3: Design of Steel Structures-Part 1. 4: General Rules-Supplementary Rules for Stainless Steels[S]. European Committee for Standardization，ENV 1993-1-4，CEN，Brussels:2006.

[2] ASCE. Specification for the Design of Cold-Formed Stainless Steel Structural Members[S]. 2002.

[3] AS/NZS. Australian/New Zealand Standard: Cold-Formed Stainless Steel Structures[S]. Sydney:Australia，2001.

[4] 日本不锈钢结构建筑协会设计基准编制委员会. 不锈钢建筑结构设计基准[S]. 2001.

[5] Lin S H，Yen S I，Weng C C. Simplified Design Approach for Cold-Formed Stainless Steel Compression Members Subjected to Flexural Buckling[J]. Thin-Walled Structures，2005，43 (12): 1831-1851.

[6] Rasmussen K J R，Rondal J. Explicit Approach to Design of Stainless Steel Columns [J]. J Struct Eng，ASCE，1997，123 (7): 857-863.

[7] Rasmussen K J R，Rondal J. Strength Curves for Metal Columns [J]. J Struct Eng，ASCE，1997，123(6):721-728.

[8] 郑宝锋. 不锈钢冷弯薄壁型钢轴心受压和偏心受压构件理论分析和试验研究[D]. 南京:东南大学，2010.

[9] Quach W M，Teng J G.,Chung K F. The-Stage Full-Range Stress-Stain Model for Stainless Steel[J]. Journal of Structural Engineering，2008，134(9):1518-1527.

[10] GB 500172003 钢结构设计规范[S].

[11] EC3. Eurocode 3: Design of Steel Structures-Part 1. 3: General Rules-Supplementary Rules for Cold-Formed Members and Sheeting[S]. European Committee for Standardization，ENV 1993-1-3，CEN，Brussels; 2006.

[12] Liu Y，Young B. Buckling of Stainless Steel Square Hollow Section Compression Members[J]. J. Constr. Steel Res.,2003，59(2):165-177.

[13] Young B，Liu Y. Experimental Investigation of Cold-Formed Stainless Steel Columns [J]. J. Struct. Eng.,2003，129 (2): 169-176.

[14] Young B，Hartono W. Compression Test of Stainless Steel Tubular Members[J]. J. Struct. Eng.,2002，128(6):754-761.

[15] Young B，Lui W M. Behavior of Cold-Formed High Strength Stainless Steel Sections[J]. J. Struct. Eng.,2005，131(11): 1738-1745.

[16] Rasmussen K J R，Hancock G J. Design of Cold-Formed Stainless Steel Tubular Members. I: Columns [J]. J. Struct Eng，ASCE，1993，119(8):2349-2367.

[17] Gardner L，Nethercot D A. Experiments on Stainless Steel Hollow Sections-Part 1: Material and Cross-Sectional Behaviour [J]. J. Constr. Steel Res.,2004，60(9):1291-1318.

[18] Gardner L，Nethercot D A. Experiments on Stainless Steel Hollow Sections-Part 2:Members Behavior of Columns and Beams[J]. J. Constr. Steel Res.,2004，60(9):1319-1332.

施引文献

资源附件(0)

访问统计