高强螺栓端板连接的撬力分析与研究

王燕; 郑杰

doi:10.13204/j.gyjz200809028

高强螺栓端板连接的撬力分析与研究

doi: 10.13204/j.gyjz200809028

王燕¹,
郑杰²

1.
1. 青岛理工大学土木工程学院,青岛 266033;
2.
2. 济宁市建筑设计研究院,济宁 272125

基金项目:

山东省自然科学基金资助项目(Y2006F10)

详细信息

作者简介:
王燕,女,1957年2月出生,教授,博士生导师,E-mail:yanwang123@qtech.edu.cn

计量
- 文章访问数: 84
- HTML全文浏览量: 10
- PDF下载量: 101
- 被引次数: 0
出版历程
- 收稿日期: 2007-10-20
- 刊出日期: 2008-09-20

STUDY ON THE PRYING FORCE OF HIGH STRENGTH BOLT IN EXTENDED END-PLATE CONNECTION

Wang Yan¹,
Zheng Jie²

1.
1. School of Civil Engineering,Qingdao Technological University Qingdao 266033;
2.
2. Jining Architectural Design &Research Institute Jining 272125

摘要

摘要: 利用有限元软件ANSYS分析和研究了外伸端板高强螺栓受拉连接接头破坏的Mises等效应力云图、端板变形、撬力分布以及螺栓拉力变化及分布。证明了撬力在端板连接中是显著存在的;增加端板厚度及设置加劲肋能够减小撬力影响;撬力的作用使高强螺栓拉力提高,外伸端板高强螺栓拉力的分布是以受压翼缘为转动中心的梯形分布。提出了考虑撬力作用的理论计算公式,算例结果表明,考虑撬力设计的计算公式较为简单并具有较好的设计适用性。
- 高强螺栓 /
- 有限元 /
- 撬力 /
- 端板连接 /
- T型接头
Abstract: ANSYS,a large general FEM software,is selected to analyze high strength bolt in extended end-plate connections,about Mises stress nephogram,deformation of end-plate,distribution of prying force and tensile force of bolt.Prying force is proved to exist according to the results of FEM analysis.The influence of prying force descends obviously by the thickness of end-plate and the stiffener.It indicates that the prying force increases the tensile force of bolt assuredly.The tensile force's distribution of high strength bolt is a trapezoid which is rolled by the center of compression flange.By the result of calculation formula,it indicates that the formula of prying force is simple and applicable for design.
- high strength bolt /
- finite element /
- prying force /
- end-plate connection /
- T-shaped connection

HTML全文

参考文献(8)

[2] 费雪 J W,斯特鲁克 J H A.螺栓和铆钉连接指南.北京:人民交通出版社,1983

GB 50017-2003 钢结构设计规范

[3] JGJ 82-91 钢结构高强度螺栓连接的设计、施工及验收规程

[4] British Standards Institution (BSl):BS 5950-1:2000.Structural Use of Steelwork in Building.Part l:Code of Praetiee for Design:Rolled and Welded Seetings.2000

[5] Shi Y J,Chan S L,Wong Y L.Modeling of Moment-Rotation Chara cteristics for Endplate Connections.Journal of Structural Engineering,ASCE,1996,122(11):1300-1306

[6] Faella C,Piluso V,Rizzano G.Reliability of Eurocode 3 Procedures for Predicting Beam to Colunto Joint Behavior // Proceeding of 3rd International Conference on Steel and Aluminum Structures.MAS Printing Co.,1995:441-448

[7] Feella C,Piluso V,Rizzano G.Experimental Analysis of Bolted Conneetion Snug Versus Preloaded Bolts.Journal of Structural Engineering,ASCE,1998,124(7):765-774

[8] Kulak G L,Fisher J W,Struik J H A.Guide to Design Criteria for Bolted and Riveted Joints.New York:John Wiley and Sons,1987

施引文献

资源附件(0)

访问统计